
Experience the convenience of spreading material with a bottom dump trailer while pulling it behind your dump truck with the Load Line Quad Cross Gate Wagon.

Bottom dump cross gate; fast acting close under load gates with adjustable gate stops for controlled spread.

This trailer uses a heavy duty Holland turntable bearing.

Our open frame design in the front and rear reduces weight and drag, increasing payload and profit.
| Width | 8'6" |
| Length | 43'1" |
| Model | LL28-QWCD |
| Overall Height | Top of sideboards: 112.5" unladen |
| Target Load Area | 94"W x 219"L |
| Bottom Hopper Opening | 22" x 94" |
| Gate Ground Clearance | 22" |
| Capacity | Level full 23.4 cu. yd., Heaped 24.9 cu. yd. |
| Axle Spread | 50" |
| Frame | Fabricated wide flange I beam mail rails on front dolly, Fabricated wide flange I beam main rails on rear suspension, Formed lightweight engineered cross members, Diffuser plates & gussets located where required to support & relieve stress |
| Turntable | Holland HD 39" grease tube turntable bearing |
| Hitch | Square tube style draw bar c/w rubber bushed pivot hinges, Premier heavy duty low profile pintle eye, Lightweight swivel jack & spring assisted draw bar lift, (2) 3-ton safety hooks @ 1/2" safety chains |
| Hopper | High tensile 1/8" formed convex sidewall, High tensile 1/8"-55 degree upper & lower slope panels, Aluminum walking deck and ladder in front of hopper, Calcium sprayer tank c/w nozzle and hose assembly at front, 2" x 8" spruce sideboards |
| Gates | High tensile formed gate panels & formed horizontal stiffeners, Composite 8" x 24" double acting air cylinders & quick return valves, Harden gate hinge pins & grease type hinge bushings, Adjustable gate spread selection @ 2" increments, 60g reservoir c/w shut off valve & safety check valve , Mac electric over air solenoid gate control valve, Bimba lubricator & filter units located in aluminum side cabinet, Par36 utility heat lamp installed in oiler cabinet |
| Bumper | Heavy duty 4” x 4” tubing bumper and uprights |
| Fenders | (4) Plastic tub style fenders over dolly tires, Aluminum sloped fenders inside & outside neck & rear tires areas |
| Landing Gear | 5000lb swivel crank down dolly leg mounted on A frame hitch |
| Rock Shields | Heavy duty rock shield installed on front side of suspension |
| Suspension | 23,000 lb. air ride, Dual electric/manual air dump & liquid filled weigh gauge |
| Axles | (3) 25,000 lb. axles @ 77.5” track (8’6” over tires) |
| Brakes | Automatic slack adjusters, Meritor/WABCO 2S/1M ABS |
| Brake Linings | 16 1/2" x 7" Q-plus quick-change brakes c/w enclosed camshafts |
| Bearings & Seals | Tapered axle bearing system & Stemco HP seals |
| Hubs & Drums | 10 stud steel piloted hubs & cast steel drums |
| Wheels | (16) Aluminum 10 stud pilot mount 24.5 x 8.25 disc - machined |
| Tires | 11R-24.5 on/off road tires |
| Electrical System | Integrated harness system, LED rubber mounted sealed beam, Midway turn signal on each side of trailer, 7 & 6 male plugs at front hitch with cords routed in hitch tubing, (4) Rear red oval tail/stop/turn lights, (3) Rear 2" center ID with front & rear corner 2" marker lights |
| Fenders | Aluminum smooth fenders installed outside neck areas & rear tires |
| Mudflaps | Standard equipped full mud flap package |
| Load Cover | Michel’s Dura-flip mesh load cover c/w electric drive winder |
| Finish | Sandblasted, epoxy primer & Axalta urethane paint, Sideboards painted with Axalta urethane paint, Single 4” & double 1” black body stripe |
| Safety Tape | Applied as per regulations |
| Warranty | 5 year pro-rated warranty on structural components manufactured by Loadline, 1 year warranty on non-structural components manufactured by Loadline |
There are no videos at this time.
To view our inventory of in stock and on order belly dumps, click the button below.