If you’re looking for reliability and versatility, the Load Line Cross Clam Belly Dump is your trailer. This trailer features a cross clam gate assembly that allows the trailer to do a thin uniform spread pattern typically associated with cross dump trailers, as well as have the same quick unloading capacity of a clam dump when the gates are wide open.
The 60” w x 62” L cross clam gates give you the option to dump in a variety of different spread patterns.
Optimum hopper slope for better material cleanout.
Our open frame design in the front and rear reduces weight and drag, increasing payload and profit.
|Overall Height||10'2" to top of sideboards|
|Target Load Area||7’10” w x 18’0” L|
|Bottom Hopper Opening||60” w x 62” L|
|Gate Ground Clearance||18"|
|Frame||6” x 4” rectangular tube perimeter frame, Manufactured high tensile I beam sub frame over suspension, Engineered formed high tensile channel crossmembers, Diffuser plates & gussets located to support & relieve stress|
|Upper Coupler||Rubber bushing, side oscillating upper coupler plate c/w 2” kingpin|
|Hopper||High tensile 50w-1/8” formed convex sidewall, High tensile 50w-1/8”- 50°upper & 60° lower slope panels, Horizontal stiffeners on end slopes & (4) sides of lower hopper, Aluminum walking deck and metal ladder in front of hopper|
|Gates||(2) ¼” formed gates with formed longitudinal stiffeners, Harden gate hinge pins & grease type hinge bushings, Composite 8” double acting air cylinders & quick return valves, Cylinder guards mounted on sides of hopper opening, Side mounted adjustable spread selection & air operated cleanouts, (1) 60-gallon air reservoir c/w shut off valve & safety check valve, Big Mac electric over air operated solenoid to gate control opening, Bimba lubricator & filter units located in a lockable side cabinet, Par36 utility heat lamp installed in oiler cabinet|
|Push Block||Bolt on push block mounted on rear apron|
|Landing Gear||Lightweight drop tube dolly legs, pin type height adjustment|
|Rock Shields||Rock shield installed on front side of 1st axle suspension|
|Suspension||(3) 23,000lb air ride suspension, Dual electric / manual air dump & liquid filled weigh gauge|
|Axles||(3) 25,000 lb. axles @ 77.5” track, Tapered axle bearing system & Stemco HP seals|
|Brakes||16 ½” x 7” Q-plus quick-change brakes c/w enclosed camshafts, Type 30/30 brake chambers, top axle mount with pushrods to rear, Haldex automatic slack adjusters|
|Hubs & Drums||10 stud steel piloted hubs & cast steel drums|
|Wheels||10 stud pilot mount steel 24.5 x 8.25 disc- White|
|Tires||11R-24.5 radial 16 ply|
|Electrical System||Integrated harness system LED rubber mounted sealed beam, (4) Rear red oval tail/stop/turn lights, (3) Rear 2” center ID with front & rear corner 2” marker lights, (1) Midway amber turn/clearance light per side of trailer|
|Fenders||Aluminum checker fenders installed outside neck areas & rear tires|
|Mudflaps||Standard equipped full mud flap package|
|Load Cover||Michel’s Dura-Flip c/w manual chain drive winder|
|Finish||Sandblasted, epoxy primer & Axalta urethane paint, Sideboards painted with Axalta urethane paint, Single 4” & double 1” vinyl body stripe|
|Safety Tape||Applied as per regulations|
|Warranty||(5) year Prorated on structural components built by Loadline, (1) year on non-structural components built by Loadline|
There are no videos at this time.
To view our inventory of in stock and on order belly dumps, click the button below.