The Centerline Cross Gate was engineered and fabricated to suit environments that demand supreme durability and zero down-time. The main I-beams are fabricated using 130,000 tensile strength T1 steel. The hopper and gate system is one of the most durable in the industry. Reinforced corners and walls in the hopper mean you never have to worry about what you’re feeding it. And heavy duty gates with super strong7” cylinders ensure a tight seal for years to come.
The 22” x 92.5” gate opening is extra large, minimizing material hang up when dumping.
Non-metallic cylinder body and end plates eliminate corrosion issues normally associated with steel cylinders.
Our open frame design in the front and rear reduces weight and drag, increasing payload and profit.
Bolt on push block assembly protects rear of trailer when in contact with a push machine.
The steep end slopes, combined with smooth, side slopes greatly improves material cleanout.
Individual guards are installed on the front side of brake pots to protect components against debris when pulling in harsh terrain.
|Overall Height||9'11" to top of sideboards|
|Target Load Area||7'10W x 17'10"L|
|Bottom Hopper Opening||22" x 92.5"|
|Gate Ground Clearance||18"|
|Capacity||27 cu. yd. with 2” x 8” sideboards|
|Frame||QT-100, I beam sub frame over tridem suspension, Lightweight engineered cross members, Diffuser plates & gussets located where required to support & relieve stress|
|Upper Coupler||Rubber bushing, side oscillating upper fifth wheel plates c/w 2” kingpin|
|Hopper||55” h formed high tensile 3/16” steel side wall panel, formed convex horizontal stiffeners, Main frame beams: 6” x 4” lower & 4” x 4” upper rectangular tube, High tensile 10 gauge 55 degree upper slope panel, formed horizontal stiffeners , 2” x 8” finished spruce sideboards|
|Gates||(2) 24”w x 94”h formed gate panels, formed longitudinal stiffeners, Composite 7” double acting air cylinders & quick return valves, Adjustable gate spread selection @ 1 ¼” increments, 60 gallon air reservoirs c/w shut off valve & safety check valve, Mac electric over air operated solenoid to control gate opening, Norgren lubricator & filter units located in lockable side cabinet|
|Push Block||Bolt on under ride protection guard assembly|
|Landing Gear||Lightweight drop tube dolly legs, pin type height adjustment|
|Rock Shields||Individual shields installed on front side of axles ahead of brake chambers|
|Suspension||(3) 30,000 lb. air ride suspension @ 60” spacing, Dual electric/manual air dump & liquid filled weigh gauge|
|Axles||(3) 25,000 lb. axles @ 77.5” track, Parallel axle bearing system & Stemco HP seals|
|Brakes||16 ½” x 7” Q Plus brake shoes enclosed camshafts, Crewson automatic slack adjusters, Meritor/WABCO 2S/1M ABS|
|Hubs & Drums||10 stud steel piloted hubs & cast steel drums|
|Wheels||10 stud piloted mounted steel 24.5 x 8.25 wheels – Silver|
|Tires||11R-24.5 radial 16 ply|
|Electrical System||Integrated harness system LED rubber mounted sealed beam, Midway turn signal on each side of trailer, Triple tail/turn/stop lights & (5) center ID lights on rear for increased visibility|
|Fenders||Aluminum smooth fenders installed outside neck areas & rear tires|
|Mudflaps||Standard equipped full mud flap package|
|Load Cover||Michel’s Dura-Flip c/w manual chain drive winder|
|Finish||Sandblasted, primed, & painted with PPG urethane paint Sideboards painted with PPG urethane paint - Black Single 4” & double 1” black body stripe|
|Safety Tape||Applied as per regulations|
|Weight||7,598 kgs +/- 2% on steel wheels (subject to option changes)|
|Warranty||1st year – 100% parts & labour; 2nd year – 50% parts & labour; 3rd to 5th year – 50% parts only|
There are no videos at this time.
To view our inventory of in stock and on order belly dumps, click the button below.
26180 – 114 Avenue,
Acheson, AB T7X 6R1