The Centerline Cross Clam dump trailer is designed specifically for contractors who haul a wide variety of products and require a more versatile dump trailer. The cross clam gate assembly allows for the trailer to do a thin uniform spread pattern typically associated with cross dump trailers, as well as have the same quick unloading capacity of a clam dump when the gates are wide open.
Our open frame design in the front and rear reduces weight and drag, increasing payload and profit.
The bolt on push block assembly protects the rear of the trailer if it comes in contact with a push machine.
This trailer comes with parallel bearing axles which reduce the amount of friction and thus heat on the brake components, ultimately allowing for easier pulling capabilities.
Individual rock shields are installed on the front side of the brake pots to protect components against debris when pulling in harsh terrain.
Including the 2” x 10” sideboards, the total hauling capacity of this trailer is 27.5 cu. yards.
Both tandem and tridem models are available and can be combined to suit your needs.
|Length||37'1", 39'2" (includes push block)|
|Overall Height||Top of sideboards: 121"|
|Hopper Load Area||7’10”W x 18'0”L|
|Bottom Hopper Opening||72”W x 76”L|
|Gate Ground Clearance||15"|
|Capacity||27.5 cu. yd with 2” x 10” sideboards|
|Frame||QT-100, I beam sub frame over tridem suspension, Lightweight engineered cross members, Diffuser plates & gussets located where required to support & relieve stress|
|Upper Coupler||Rubber bushing, side oscillating upper 3/8” fifth wheel plates c/w 2” kingpin|
|Hopper||High tensile AR200 5mm formed convex sidewall, High tensile 55w, 1/8” 51°- 58° front & rear slope panels, Horizontal stiffeners on end slopes & (4) sides of lower hopper, Aluminum catwalk & ladder for access to front side of hopper, 20L calcium sprayer, spray gun & hose assembly beside ladder|
|Gates||High tensile 55w,3/16” formed panels c/w longitudinal stiffeners, 8” Double acting composite air cylinders, Harden gate hinge pins & grease type hinge bushings, Electronic gate spread selection switch & clean out override, 60 Gallon air reservoirs c/w shut off & safety check valve, Big Mac electric over air operated solenoid to gate control opening, Norgren oil lubricator & water filter mounted in side cabinet, Par 36 utility heat lamp & switch installed in valve cabinet|
|Bumper||Bolt on rear push block & (2) tow rings|
|Landing Gear||Light weight drop tube dolly legs, pin type height adjustment|
|Rock Shields||Rock shields mounted on all axles ahead of brake chambers|
|Suspension||(3) 25,000 lb. air ride suspension, Dual electric/manual air dump & liquid filled weigh gauge|
|Axles||(3) 25,000 lb. axles @ 77.5” track c/w parallel spindles|
|Brakes||16 ½” x 7” Q Plus brake shoes c/w enclosed camshafts, Automatic slack adjusters, Parallel axle bearing system & Stemco HP seals Meritor/WABCO 2S/1M ABS|
|Hubs & Drums||10 stud steel piloted hubs & cast steel drums|
|Wheels||10 stud piloted mounted steel 24.5 x 8.25 wheels – Silver|
|Tires||11R-24.5 radial 16 ply|
|Electrical System||Integrated harness system LED rubber mounted sealed beam, Midway turn signal on each side of trailer|
|Fenders||Sloped steel fenders installed neck areas and over rear tires|
|Mudflaps||Standard equipped full mud flap package|
|Load Cover||Michel’s Dura-Flip c/w manual chain drive winder|
|Finish||Sandblasted, primed, & painted with PPG urethane paint Sideboards painted with PPG urethane paint - Black Single 4” & double 1” black body stripe|
|Safety Tape||Applied as per regulations|
|Weight||7,257kgs +/- 2% on steel wheels (subject to option changes)|
|Warranty||1st year – 100% parts & labour; 2nd year – 50% parts & labour; 3rd to 5th year – 50% parts only|
There are no videos at this time.
To view our inventory of in stock and on order belly dumps, click the button below.
26180 – 114 Avenue,
Acheson, AB T7X 6R1